Sunshine belt~ALLED Lighting

alled lighting

This article is telling about the different sockets names and basis, sizes. For example LED Replacement Bulb.You may use the light, but you don't know much about the details, I found it from wikiHow website, as below is the address, for your interesting,you can take have a look.
http://www.wikihow.com/Tell-the-Differences-Among-the-Light-Sockets

alled lighting

Hello everybody, i have found an article from wikiHow about "how to take a necessary modification to make a 12v input voltage designed light suitable to be used at external 240V mains electricity? That article shows modification of the light power charging battery, so people can use the external 240V voltage to power the light through a transformer. There are two ways to show you how to do it. As below is the article address for your reference.

http://www.wikihow.com/Use-a-12V-DC-at-240V-AC-Transformer-to-Connect-with-a-LED-Light

alled lighting

Just a quick note to demonstrate how simple it is to obtain power from your mains electricity to your 12V DC strip light.
There are 2 Ways. A small yet satisfying job. Much easier than expected!

The first Method:

Parts:
- 12V DC 500mm LED Strip Light from ebay
- Mains electricity
-Caravan & Camper Battery Charging
-3M quick connect cable with cigarette connector
-Battery terminal

Labor:
- About 10-20 mins to investigate your lights to determine how they work.
- About 15 mins to install.

1.Turn off your mains electricity.

2. Connect your mains electricity

to your caravan & camper Battery Charging

3. Cut the Battery terminal clamp and take the plastic cover off to leave the wire outside, connect the wire at the 12V DC end of the transformer for positive and negative line tightly.

4.Plug the3M quick connect cable with cigarette connector into the Battery terminal

5.Connect the 3M quick connect cable with cigarette connector to your strip light.

6. Turn on your mains electricity, then the light is on.

The second Method:

Parts:
- 12V DC 500mm LED Strip Light from ebay
- Mains electricity
-Caravan & Camper Battery Charging
-3M quick connect cable with cigarette connector

Labor:
- About 10-20 mins to investigate your lights to determine how they work.
- About 15 mins to install.

1.Turn off your mains electricity.

2. Connect your mains electricity

to your caravan & camper Battery Charging

3. Cut the 3M quick connect cable with cigarette connector and connect the wire at the 12V DC end of the transformer for positive and negative line tightly.

4. Connect the 3M quick connect cable with cigarette connector to your strip light

5. Turn on your mains electricity, then the light is on

alled lighting

www.alled.com.au stores.ebay.com.au/alled stores.ebay.com.au/jayco-led

alled lighting

www.alled.com.au www.stores.ebay.com.au/alled www.stores.ebay.com.au/jayco-led

alled lighting

You received this email beacuse you are involved with our online business. If you prefer not to receive emails from ALLED, you can unsubscribe here.

About Us

ALLED provides wide range of LED products. Welcome to our online store.

www.alled.com.au

stores.ebay.com.au/jayco-led

stores.ebay.com.au/alled

alled lighting

Tips to be a hit at night~tutorial to fix the led underbody light
Underbody light is a board lighting accompany ,playing as the underbody lamp for the 4X4 vehicle, caravan or even boat and marine.

The gallery for distinctive LED lighting from underbody
As far as the utilization in off road dri ving ,just like a common sense to offroad enthusiasts , underbody light is essential for the ugged trap or other trap occasions where the& nbsp;tyre situation has to be confirmed at nigh t road.
After checking if the underbody lamp is allowed in your state , ensure the regu lation for the color and position place , you may need the tutorial for installation.
1. Wheel for sufficient mounting room ,recommend you take the left wheeling which is for the better space for ease installation.

Turn the steering for installation space
2. Locate and mark the installation point under the chassis or other invisible areas of vehicle, the referenced fixing point ;should be away from high- heat areas ,avoid electrical wires and fuel line.

Mark the mounting point
3. Drill proper mounting hole. Use the s maller bit for slow and cautious drill in case of the mounting hole turns out to be too large to fasten the light body. And pay attention not to drill too deep to avoid damaging the inner components.
4. Cover some silicone on the lamp botto m. It is not only for sticking but for anti-vibration protection according to the practical road situation. And choose the thick silicone if possible.

Apply the silicone coat
5. Screw up, don’t forget to select&nbs p;the mounting bolts in proper length, too long tends to add the difficulty in fixing and inner damage. Too short is not sufficient for mounting.

Screw up the LED underbody lamp
6. Route the wiring to the battery and&n bsp;connect the toggled switch under the dash b oard. The switch make it ease to control t he underbody lighting by sitting on seat. When you are on the course of connection, please make sure the power source box is s hut down.
7 . Turn on the electricity source, and c heck the output lighting.

Check your result of hardwork
When you are trapped on the road to an exciting driving journey at night, the LED Underbody lightcan do you from the invisible nook, not general usage but essential preparation, you might as well bring one to promise the easy and ease on your way home or for venturing .