Do you have any ideas about differences Among the Light Sockets?

This article is telling about the different sockets names and basis, sizes. For example LED Replacement Bulb.You may use the light, but you don't know much about the details, I found it from wikiHow website, as below is the address, for your interesting,you can take have a look.
http://www.wikihow.com/Tell-the-Differences-Among-the-Light-Sockets

How to modify a 12V input voltage designed light suitable to be used at external 240V mains electricity?

Hello everybody, i have found an article from wikiHow about "how to  take a necessary modification to make a 12v input voltage designed light suitable to be used at external 240V mains electricity? That article shows modification of the light power charging battery, so people can use the external 240V voltage to power the light through a transformer. There are two ways to show you how to do it. As below is the article address for your reference. 

http://www.wikihow.com/Use-a-12V-DC-at-240V-AC-Transformer-to-Connect-with-a-LED-Light

How your 12V DC strip light can get the power from your mains electricity

---

Just a quick note to demonstrate how simple it is to obtain power from your mains electricity to your 12V DC strip light.
There are 2 Ways. A small yet satisfying job. Much easier than expected!

The first Method:

Parts:
- 12V DC 500mm LED Strip Light from ebay
- Mains electricity
-Caravan & Camper Battery Charging
-3M quick connect cable with cigarette connector
-Battery terminal



Labor:
- About 10-20 mins to investigate your lights to determine how they work.
- About 15 mins to install.

1.Turn off your mains electricity.

2. Connect your mains electricity to your caravan & camper Battery Charging

3. Cut the Battery terminal clamp and take the plastic cover off to leave the wire outside, connect the wire at the 12V DC end of the transformer for positive and negative line tightly.

4.Plug the3M quick connect cable with cigarette connector into the Battery terminal

 

5.Connect the 3M quick connect cable with cigarette connector to your strip light.

6. Turn on your mains electricity, then the light is on.

The second Method:

Parts:
- 12V DC 500mm LED Strip Light from ebay
- Mains electricity
-Caravan & Camper Battery Charging
-3M quick connect cable with cigarette connector





Labor:
- About 10-20 mins to investigate your lights to determine how they work.
- About 15 mins to install.

1.Turn off your mains electricity.

2. Connect your mains electricity to your caravan & camper Battery Charging

3. Cut the 3M quick connect cable with cigarette connector  and connect the wire at the 12V DC end of the transformer for positive and negative line tightly.

4. Connect the 3M quick connect cable with cigarette connector to your strip light

5. Turn on your mains electricity, then the light is on

Boating trip preparation

www.alled.com.au     stores.ebay.com.au/alled     stores.ebay.com.au/jayco-led

RV Camping Trip

www.alled.com.au         www.stores.ebay.com.au/alled         www.stores.ebay.com.au/jayco-led

led work light price drop off

You received this email beacuse you are involved with our online business. If you prefer not to receive emails from ALLED, you can unsubscribe here.

About Us

ALLED provides wide range of LED products. Welcome to our online store.

www.alled.com.au

stores.ebay.com.au/jayco-led

stores.ebay.com.au/alled

Tips to be a hit at night~tutorial to fix the led underbody light

Tips to be a hit at night~tutorial to fix the led underbody light Underbody light is a board lighting accompany  ,playing as the underbody lamp for the 4X4  vehicle, caravan or even boat and marine. The gallery for distinctive LED lighting from underbody As far as the utilization in off road dri ving ,just like a common sense to offroad  enthusiasts , underbody light is essential for  the ugged trap or other trap occasions where the& nbsp;tyre situation has to be confirmed at nigh t road.  After checking if the underbody lamp  is allowed in your state , ensure the regu lation for the color and position place ,  you may need the tutorial for installation. 1. Wheel for sufficient mounting room ,recommend you take the left wheeling which is for the better space for ease installation. Turn the steering for installation space 2. Locate and mark the installation  point under the chassis or other invisible areas of vehicle, the referenced fixing point  ;should be away from high- heat areas ,avoid electrical wires and fuel line.  Mark the mounting point 3.  Drill proper mounting hole. Use the s maller bit for slow and cautious drill in  case of the mounting hole turns out to be too large to fasten the light body. And pay attention not to  drill too deep to avoid damaging the inner components.  4.  Cover some silicone on the lamp botto m. It is not only for sticking but for anti-vibration protection according to the practical road  situation. And choose the thick silicone if possible.                                                                                                                                                        Apply the silicone coat 5.  Screw up, don’t forget to select&nbs p;the mounting bolts in proper length, too long  tends to add the difficulty in fixing and  inner damage. Too short is not sufficient for mounting.                                                                                                                                                 Screw up the LED underbody lamp 6.  Route the wiring to the battery and&n bsp;connect the toggled switch under the dash b oard. The switch make it ease to control t he underbody lighting by sitting on seat. When you are on the course of connection,  please make sure the power source box is s hut down. 7 . Turn on the electricity source, and c heck the output lighting.  Check your result of hardwork When you are trapped on the road to an exciting driving journey at night, the LED Underbody lightcan do you from the invisible nook, not general usage but essential preparation, you might as well bring one to promise the easy and ease on your way home or for venturing .

Fishing Trip

www.alled.com.au     stores.ebay.com.au/alled     stores.ebay.com.au/jayco-led

gift voucher

Hiking Trip

www.alled.com.au     stores.ebay.com.au/alled     stores.ebay.com.au/jayco-led

How to fix the underbody light on your lovely car?

Tips to be a hit at night~tutorial to fix the led underbody light Underbody light is a board lighting accompany  ,playing as the underbody lamp for the 4X4  vehicle, caravan or even boat and marine. The gallery for distinctive LED lighting from underbody As far as the utilization in off road dri ving ,just like a common sense to offroad  enthusiasts , underbody light is essential for  the ugged trap or other trap occasions where the& nbsp;tyre situation has to be confirmed at nigh t road.  After checking if the underbody lamp  is allowed in your state , ensure the regu lation for the color and position place ,  you may need the tutorial for installation. 1. Wheel for sufficient mounting room ,recommend you take the left wheeling which is for the better space for ease installation. Turn the steering for installation space 2. Locate and mark the installation  point under the chassis or other invisible areas of vehicle, the referenced fixing point  ;should be away from high- heat areas ,avoid electrical wires and fuel line.  Mark the mounting point 3.  Drill proper mounting hole. Use the s maller bit for slow and cautious drill in  case of the mounting hole turns out to be too large to fasten the light body. And pay attention not to  drill too deep to avoid damaging the inner components.  4.  Cover some silicone on the lamp botto m. It is not only for sticking but for anti-vibration protection according to the practical road  situation. And choose the thick silicone if possible. Apply the silicone coat 5.  Screw up, don’t forget to select&nbs p;the mounting bolts in proper length, too long  tends to add the difficulty in fixing and  inner damage. Too short is not sufficient for mounting.                Screw up the LED underbody lamp 6.  Route the wiring to the battery and&n bsp;connect the toggled switch under the dash b oard. The switch make it ease to control t he underbody lighting by sitting on seat. When you are on the course of connection,  please make sure the power source box is s hut down. 7 . Turn on the electricity source, and c heck the output lighting.  Check your result of hardwork When you are trapped on the road to an exciting driving journey at night, the LED Underbody lightcan do you from the invisible nook, not general usage but essential preparation, you might as well bring one to promise the easy and ease on your way home or for venturing .

Yellow light to keep night flying insects away.
ALLED is launching a new patent product at market at Mid of May, which is a dual color LED Camping Light, which includes a programmed dimmer switch to adjust the light between yellow and cool white light. And the yellow lighting function is part of our patent content for this light. Some may become confused that what is the function of the yellow light. To explain it, please you may be mentioned of one situation. If you have carefully observated your outdoor security night, you may find that insects and bugs keep circling around and around. You will find the same situation for the road light. So image the situation that if you are on camping trip at night, what is your feeling when you are boring by a set of insects? At that situation, if you have our light at hand, you are sure to be free from that hassel. So you may ask why a light has a yellow light plus will have that effect? To explain that, first you need to understand why insects are attracted to lights? People may have the normal sense that insects and bugs will be attracted to lights. Actually it is not the fact, only night flying insects are attacted by lights. So why?
There is no single scientific explanation for this behavior, however.Some explanation may be reference.
One saying it is that, Nigh flying insects are evolved to navigate by the light of the moon. By keeping the moon's reflected light at a constant angle, the insects can maintain a steady flight path and a straight course. Artificial lights interfere with an insect's ability to detect the moonlight. They appear brighter, and radiate their light in multiple directions. Once an insect flies close enough to a light bulb, it attempts to navigate by way of the artificial light, rather than the moon.
One explanation is that, Light is treated as the sign to seperated Up and Down for night flying insects. As most insets are living in an environment that are surrounding by plants. So for insects, this is normal sense that, it become darker when more closed to the ground. At the opposite, when higher to the sky, it become lights. Besides, for insects, their hunters are more likely to appear on the ground. So for safety consideration, they will fly higher into the sky. At this sense, the light will be the sign of the high position. So it will be one explanation for reason that insects will be attracted by lights.
Actually not all lights will attract insects. Some kind of light radiatioin attracts insects, while some not. Insects are sensitive to a broad spectrum of light ranging from ultraviolet(UV) to red. Color sensitivity in UV spectrum plays an important role in navigation in flying and terrestrial invertebrate animals. Behavioral and electrophysiological experiements found that the insect eye responds to ultraviolet irradiation. This response leads to several different reactions. When insects are exposed to light, they may go toward or keep away from the source of illumination. For example, many insects forage at twilight when blue dominate the irradiance spectrum the sky.
A LED is a semiconductor lighting source. Originally, LEDs were introduced as a practical electronic component in 1962 and early LEDs emitted low-intnesity red light. However, modern version are available across the visible, ultraviolet and infrared wavelenghts, with very high bright light. Based on our knowledge of insect vision and colors across the visible spectrum, it can be assumed that if the LED light emission is towards the higher end of visible spectrum(>550nm), it may be out of the range of vision of most insects. However if the LED light is within the range you can assure that it is visible by insects.